surface mount polymer esd suppressors low capacitance revision november 28, 2013 1 / 4 @socay electronics co., ltd. 2013 specifications are subject to change without notice. please refer to www.socay.com for current information. esd0402e - esd0603e socay electronics co., ltd. www.socay.com this specification is applied to electrostatic discharge (esd) protection. it is designed to protect the high-speed data lines against esd transients. it has very low capacitance and fast turn on times makes it ideal for data and transmission lines with high data rates. according to the special property of device, we recommend not to use on such application as dc/ac power line. u rohs compliant, lead-free and available halogen-free u protection against esd voltages and currents (iec 61000-4-2 level 4) u extremely quick response time (<1 ns) present ideal esd protection u extremely low capacitance u extremely low leakage current u bi-directional device u surface mount device u zero signal distortion u antenna circuit u usb2.0 / usb3.0 u ieee-1394 u dvi u hdmi u digital video equipment u mobil phone u gps antenna u bluetooth communication equipment esd voltage capability rated voltage v dc (v) leakage current i l ( a) peak voltage v p (v) trigger voltage v t (v) clamping voltage v c (v) capacitance c p @1mhz (pf) response time (ns) contact discharge (kv) contact discharge (kv) esd pulse withstand (pulses) part number max. typical typical typical typical typical max. max. typical typical typical esd0402e002m05 5 0.01 300 300 30 0.2 0.5 1 8 15 1000 ESD0402E002M12 12 0.01 300 300 30 0.2 0.5 1 8 15 1000 esd0603e002m05 5 0.01 300 300 30 0.2 0.5 1 8 15 1000 esd0603e002m12 12 0.01 300 300 30 0.2 0.5 1 8 15 1000 esd0603e002m24 24 0.01 300 250 30 0.2 0.5 1 8 15 1000 v p - the peak voltage value shall be measured under the following conditions. esd test conditions:iec61000-4-2, 8kv contact discharge v t - measurement by using transmission line pulse (tlp) v c - measurement by using transmission line pulse (tlp) c p - device capacitance measured with 1vrms product model applicable electrical characteristics equivalent circuits description features
surface mount polymer esd suppressors low capacitance revision november 28, 2013 2 / 4 @socay electronics co., ltd. 2013 specifications are subject to change without notice. please refer to www.socay.com for current information. esd0402e - esd0603e socay electronics co., ltd. www.socay.com (1) series type: esd guard tm series (2) chip size (eia): 0402 / 0603 (3) series type: emi / esd protection (4) capacitance: value - exxx, e002=0.2pf (5) capacitance tolerance: n - 30%, m - 20% (6) rated voltage, vdc substrate ceramic (alumina) symbol 0201 0402 0603 encapsulate polymer l 0.63 0.05 1.00 0.10 1.60 0.1 end termination ag / ni / sn w 0.30 0.03 0.50 0.10 0.85 0.15 h 0.23 0.05 0.34 0.10 0.51 0.05 b 0.165 0.05 0.20 0.15 0.30 0.20 a 0.35 0.05 0.50 0.10 0.75 0.10 c 0.35 0.05 0.50 0.10 0.75 0.10 d 0.35 0.05 0.50 0.10 0.75 0.10 e xplanation of part num ber construction & dimensions unit: mm recommended pad outline esd 0 402 e 00 2 m 05 (1) (2) (3) (4) (5) (6)
surface mount polymer esd suppressors low capacitance revision november 28, 2013 3 / 4 @socay electronics co., ltd. 2013 specifications are subject to change without notice. please refer to www.socay.com for current information. esd0402e - esd0603e socay electronics co., ltd. www.socay.com item specifications test condition reference parameter value unit operating temperature -55 to +125 c bias humidity i l 10 a 90%rh, 40 c ,rated voltage, 1000hrs mil-std-202 method 103 storage temperature --55 to +125 c storage temperature 5 to 40 c thermal shock i l 10 a -40 c to +85 c 30 min. cycle, 5 cycles jis c0025 (1998)test na relative humidity <65 %rh taping package storage condition storage time 12 max month high temperature i l 10 a rated voltage, 85 c, 1000hrs mil-std-202g method 108 solder leach resistance i l 10 a 260 c, 10s mil-std-202g method 210f i l - leakage current at rated voltage, the maximum leakage current was measured after reliability test. reflow condition pb free assembly -temperature min (t s(min) ) +150 c -temperature max (t s(max) ) +200 c pre heat -time (min to max) (t s ) 60 -180 seconds average ramp up rate ( liquidus temp t l ) to peak 3 c/second max t s(max) to t l - ramp-up rate 3 c/second max - temperature (t l ) (liquidus) +217 c reflow - time (min to max) (t l ) 60 -150 seconds peak temperature (t p ) 260 +0/-5 c time within 5 c of actual peak temperature (t p ) 20-40 seconds ramp-down rate 6 c/second max time 25 c to peak temperature (t p ) 8 minutes max note that this product will be easily damaged by rapid heating, rapid cooling or local heating. do not give heat shock over 100 c in the process of soldering. we recommend to take preheating and gradual cooling soldering gun procedure note the follows, in case of using solder gun for replacement. 1) the tip temperature must be less than 280 for the period within 3 seconds by using soldering gun under 30w 2) the soldering gun tip shall not touch this product directly. soldering volume note that excess of soldering volume will easily get crack the body of this product. environmental specifications temperature specifications construction & dimensions unit: mm ramp-down preheat critical zone t l to t p time to peak temperature (t 25 to peak) t p t l t s(max) t s(min) 25 temperature ramp-up time precaution for soldering
surface mount polymer esd suppressors low capacitance revision november 28, 2013 4 / 4 @socay electronics co., ltd. 2013 specifications are subject to change without notice. please refer to www.socay.com for current information. esd0402e - esd0603e socay electronics co., ltd. www.socay.com carrier tape dimensions unit: mm symbol 0201 0402 0603 a 8.00 0.30 8.00 0.30 8.00 0.30 b 3.50 0.05 3.50 0.05 3.50 0.05 c 1.75 0.10 1.75 0.10 1.75 0.10 d 2.00 0.05 2.00 0.05 4.00 0.05 e 4.00 0.10 4.00 0.10 4.00 0.10 f 1.50 0.10 1.50 0.10 1.50 0.10 l 0.71 0.02 1.19 0.05 2.02 0.20 w 0.39 0.03 0.69 0.05 1.27 0.15 t 0.42 0.03 0.48 0.03 0.60 0.03 packaging method - products shall be heat-sealed in the chip pocket, spacing pitch 2-mm of paper carrier tape with cover tape, and carrier tape shall be reeled to the reel. - tape material to be paper. - cover tape adhesion to be 40 15 grams. taping reel dimensions unit: mm taping specifications there shall be the portion having no product in both the head and the end of taping, and there shall be the cover tape in the heat of taping. quantity of products in the taping package 0402 10000pcs / reel standard quantity 0603 5000pcs / reel shipping quantity is a multiple of standard quantity packaging information
|
